tripletaya.blogg.se - Liftmaster wireless keypad

LIFTMASTER WIRELESS KEYPAD INSTALL

Press and hold the PROGRAM button again then release.Press and hold the PROGRAM button until both LED lights turn BLUE.Program the keypad for a single doorOn the power head: Wireless Keypad ( Model OKP-BX) with CodeDodger ® Program Keypad for One Garage Door (CodeDodger 2) Create Your Wireless Keypad PIN (Personal Identification Number) On your wireless keypad: Mark the bottom hole, then screw in the bottom screw.Īdditional AssistanceShould you need additional information about installing or programming your garage door opener or remote, please call customer service at 1-80, or use our distributor locator to find a Red Ribbon Distributor near you.

LIFTMASTER WIRELESS KEYPAD INSTALL

Install a screw into the top drilled hole, leaving a 1/8" gap between the screw head and the wall.

Drill a 1/16" hole for the top mounting screw.

If the red LED does not blink during use, the battery needs to be changed.

After a few seconds, the LED will turn off, and you can retry.

Rapid blinking of the LED indicates an error.

Any keypad button will control the door for 30 seconds after the door starts moving.

If the LED blinks rapidly, the PIN was entered incorrectly.

If the garage door does not move, check the red LED on the keypad.

Each door opener must be programmed to receive the signal from the wireless keypad.

Repeat steps one through five for programming each garage door opener.

Press the arrow up/down triangle button a third time.

Press the arrow up/down triangle button a second time.

Press the number you have picked for this door opener: 1, 2 or 3.

“Learn Code” indicator LED continues to blink.

Enter your PIN and press the arrow up/down triangle button.

“Learn Code” indicator LED (on opener) blinks.

Decide which door will be Door 1, 2 and 3.

Press the PROG button a third time (red LED blinks several times and turns off).

Press the total number of doors you wish to control (either 2 or 3).

Press the PROG button a second time (red LED blinks twice per second).

Enter your PIN and press the PROG button (red LED blinks once per second).

Programming Two or Three Garage Door Openers All garage door openers will use the same PIN. Press the button with the arrow up/down triangles a third time.The “Learn Code” indicator LED will turn off. Press the button with the arrow up/down triangles a second time.The “Learn Code” indicator LED will stay on. Press the button with the arrow up/down triangles.Press the “Learn Code” button once (red LED indicator will blink).Locate the “Learn Code” button and the “Learn Code” red LED indicator. Getting Started Before you begin, be aware of the following: For convenience, program your keypad before mounting.If programming your garage door opener is disrupted at any point due to program failure, clear/reset your keypad. Press the PROG key again (red LED blinks twice per second and turns off).Enter your PIN (three to eight characters).Press the following keys in order: 3, 5, 7, PROG (red LED blinks once per second).Press the key with the arrow up/down triangles.

Enter your personal identification number (PIN).

Yellow Learn Button (Security+ 2.Wireless Keypad ( Model OWK-BX ) Instructions Testing Garage Door Opener.

Purple Learn Button (Security+, 315MHZ).

Orange Learn Button (Security+, 390MHZ).

Green Learn Button (Billion Code, 390MHZ).

Keypad lights up to allow for easy use, day or night.

Temporary PIN can be programmed for deliveries or guests.

Single button closure simplifies a secure exit.

Wireless design can be installed and programmed in minutes.

Works with all LiftMaster openers from 1993 to present (any LiftMaster opener with Safety Sensors).Access home or garage with a 4-number PIN.Less steps, simpler setup than the 877MAX.Replacement for the 877MAX Wireless Keypad.It is backwards compatible and has the same standard setup as all security+ 2.0 garage door openers (yellow learn button). The 878MAX simplifies the installation process of the 877MAX by removing unnecessary button prompts and reduces it to an easy four step process. The 878MAX is a replacement for the 877MAX. The 878MAX Wireless Keypad Garage Door Opener is a versatile and secure keyless entry from Northshore Commercial Door.